JavaScript is disabled. Because that a better experience, please allow JavaScript in her browser before proceeding.

You are watching: 2018 honda pilot center console removal


I stored my Kindle in the facility console and also suspect it slide down and somehow is preventing the door from sliding open. I"ve make the efforts rocking the truck and also trying to relocate it enough to gain it to on slide open but no luck. Any ideas regarding what I deserve to do besides acquisition it in to the dealer or a body shop?:frown:
I had actually this happen with one iPad. I had to snap off the back piece from the earlier seat. Begin at the bottom corners near the floor vents, get under the carpet and also give that a an excellent yank. You will feel a ar to gain your fingers. It is organized on through clips. This will eliminate the sides of the sliding door to reveal the track and give you enough flex to get the door open. I popped mine out of the track but I put everything earlier without issue. I was on the road and also did not have any kind of screw drivers. I am certain being home would have it made that a little easier.
*

Reactions:Sparkland, zroger73 and also bigbluesd
Thank you cjlee89, I"ll offer that a shot! i wish they"d have engineered that better to stop that indigenous happening.
Reactions:cjlee89
I simply hit the crap out of the sides of the console until my children ipad level down and I to be able to open it. Now I make sure the small sliding tray is constantly on optimal of the ipad to stop the ipad native lifting and also jamming the lid closeup of the door again.

See more: We Are Farmers Jingle Commercial Lyrics, We Are Farmers! Bum


Reactions:SmilinSteve, ST1300Rider, GreginJaxFL and also 2 others
*

Ran in come a trouble this morning v my center console. The cover acquired slid totally closed and also caught one of the USB charging cables over the height of the latch. No method to obtain that cable the end of there v it closed. Quit at my regional dealer who printed me an explosive diagram of the console which got me started.What friend will must do if her latch it s okay stuck top top a RTL-E trim (may different for various other trim levels)Tools: #2 Phillips driver (14 screws to remove)Trim panel device (medium plastic pry bar)Start by placing both front seats together far earlier as feasible with the arm rests in the up position. Next remove the rubber tray that is right listed below the center stack. This will disclose the first two screws that need to come out. Remove and collection aside. Making use of the trim pry bar, gentle pry between the shiny black plastic that has the cup holders and gear shifter and the slide cover until it mr free. Gently work this up and also rotate 90 levels to gain over the shifter. I did not disconnect cables. There is much more than enough slack to set to the next in the passenger foot well.Using the pry tool. Gently pry in ~ the former of the height cover the goes around the sliding door. Over there are just plastic clips holding it in and it come off really easily. As soon as you get to the back cover, tenderness lift up on the peak cover and push both pieces toward the rear seat. This will free the back panel and allow you to easily remove the height cover. This discover the twelve (12) screws the will should come out to get the sliding cover off. Beginning at the rear, there are two that go into the behind vent assembly, quickly seen from the rear seat. Remove these screws. Following remove the five that space down either side visible indigenous the top. Elevator up and also remove the rear cross bracket and the vent assembly. Following pull increase on the front sides gently it spins the side rails come free. As soon as this happens, the cover will certainly come out and also you can get to what is blocking the latch. In my case, I had actually to traction the cord up under the front dashboard to get enough play in the latch to open up it. Once free, ns cleaned the entire assembly v a vacuum because dog hair. Instead of was relatively straightforward. I started by acquisition the two side rails and also getting lock positioned therefore the behind ends were in towards the earlier seats. Following I slid the cover in come the side pieces. As soon as in, tenderness align the side rails over the guide pins. They should snap in with a small pressure. Next replace the front and also rear overcome rails. These simply snap in come place. Start replacing the screws v the 2 that go in native the ago and work your means forward. Hand tighten. All are going in to plastic and also you don"t want to break or piece a connector. Because that the plastic trim, connect the optimal to the ago cover, then seat the top on the console. Using the palm of her hand, chair the earlier cover in firmly starting on one reduced side and also finishing through the other. Girlfriend may have to wrestle v this a bit to obtain it aligned but when that is aligned, it goes together nicely. Change the shiny black color plastic covering next, being careful of her wiring and snap in place. Change the last 2 screws and also the rubber mat. Job done.I did have actually one extra step and removed the screw that held the driver side panel come the facility stack so ns could better run mine dash camera power cord as much as the plug.All in every it take it me roughly 35 minutes to complete. Naught broken and everything works choose it should. Hope this helps someone out. There room a bunch the pictures below for recommendation in instance you have actually questions.
2019 Ridgeline RTL-E modern-day Steel Metallic2016 Accord EXL White Orchid Pearl2015 Kubota B32002008 CRV EXL Red