How come Reset/Relearn 4Runner TPMS Light

4 jogger 2004-2007 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Initialization is NOT required if re-inflating tires come the at this time specified tires pressure.

You are watching: 2006 toyota 4runner tire pressure light reset

NOTE: The device will have to be initialized once tires space rotated; tires are replaced with tires of various pressures; tire push sensor and/or tire pressure monitor ECU space replaced. Collection tire pressure within the specified selection before initializing. See Initializing Tire pressure Monitor System. When a tire press sensor and/or tire push monitor ECU space replaced, the sensor ID should be memorized by the tire push monitor ECU former to mechanism initialization. See Tire pressure Sensor Registration.

Tire push Monitor Warning Light

NOTE: The tire press warning light may turn on due to natural reasons such as organic air leaks or tires pressure alters caused through temperature. In this case, adjusting the tire press will rotate off the warning light.When the tire push warning light does no go off, or when it comes on during driving, check tire push (including preventive tire) and change as necessary. The warning light must turn turn off after a few minutes. If the warning irradiate is tho on also though the tire press is correctly adjusted, the tire might be punctured. Repair together necessary. If the warning light is tho on or blinks, there is a failure in the TPM system. See proper manufacturer organization information.

Under the complying with conditions, the system may not role properly:

The areas, facilities or tools that use similar radio wave frequencies are located in the vicinity that the vehicle.A radio an equipment of comparable frequency is supplied in or close to the vehicle. Together A many snow or ice cream is grounding to the vehicle, particularly the wheels and also around the wheel houses.The battery the the sensor has actually been depleted. Together A tires without tire push monitor valve sub-assembly is used. Tire chains room used.If any other wheels 보다 the mentioned ones room used, the system may not duty properly due to the fact that the radio tide are in different way transmitted indigenous the tire press sensor.Depending on the tire type, the system might not duty properly even though the stated wheels space used.

Initializing Tire pressure Monitor System

NOTE: The device will have to be initialized once tires are rotated; tires are replaced with tires of various pressures; tire push sensor and/or tire press monitor ECU room replaced; or when a brand-new vehicle is delivered. Collection tire pressure within the specified selection before initializing.

NOTE: when initializing the system, the existing tire problem is stored together a standard.


During initialization, the tire press monitor valve sub-assembly steps the inflation press of the tires, and registers the signals that space transmitted into the tire pressure monitor ECU in ~ a frequency that one per 3 minutes. The initialization procedure is completed once the signal from the 5 tires have been received.

1. Set the tire press of every wheels (including preventive tire) to press specified top top the tire and loading info label.2. With the car stopped and parking brake applied, rotate the ignition move to the top top position.3. Press and also hold the tire push warning reset switch until the tire push warning lamp blinks 3 time at one-second intervals.4. Confirm that initialization is finish using the hand-held tester. First select “DATA LIST” ~ above the handheld tester, climate verify that the “TIREPRESS” values room displayed. It might take 5 come 6 minutes for the “TIREPRESS” worths to display screen on the hand-held tester screen

NOTE: The initialization procedure takes 5 to 6 minutes to be completed. The initialization process can be terminated by connecting terminals 4 (TC) and also 13 (CG) that the DLC3.

Tire push Sensor Registration

NOTE: If the tire push sensor and/or tire pressure monitor ECU are replaced, the transmitter ID requirements to it is in registered in the tire press monitor ECU front to system initialization. To perform this procedure, the Toyota hand-held tester have to be used.

Register Transmitter ID

1. Set the tire push of every wheels (including preventive tire) to push specified on the tire and loading info label.2. Affix the hand-held tester come DLC3.3. Rotate ignition move to on position.4. Pick the “REGIST TIRE” mode. See Fig. 14 and Fig. 20 .

*
*
5. Input the transmitter IDs (ID1 to ID5) utilizing the hand-held tester and transmit it to the tire push monitor ECU.6. Set the identifier transmission problem to “SUCCEEDED”.

NOTE: If steps 4-6 are not completed within 5 minutes, the mode will return to the normal operation mode.

Confirmation of Transmitter id Registration

1. Collection the tire push of every wheels (including spare tire) to the mentioned value.2. Connect the hand-held tester to DLC3.3. Revolve ignition switch to on position.4. Select “DATA LIST” mode on the hand-held tester.5. Check the “TIREPRESS” worths are presented on the hand-held tester screen.

4 jogger 2008-2014 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Reset is NOT required if re-inflating tires to the right now specified tire pressure.

NOTE: once a tire push sensor and/or tire pressure monitor ECU space replaced, the sensor ID must be memorized by the tire pressure monitor ECU. Watch Tire

Pressure Sensor Registration.


NOTE: If the an unfavorable battery terminal is disconnected, initialize the following system after ~ the terminal is reconnected: Power home window Control System. Describe owner’s manual or suitable manufacturer service information.

Tire push Monitor Warning Light

When the tire pressure warning irradiate does not go off, or as soon as it comes on throughout driving, check tire push and adjust as necessary. The warning light have to turn turn off within a few minutes. If the warning irradiate is quiet on also though the tire pressure is correctly adjusted, the tire can be punctured. Repair together necessary. If the warning light turns on within several hours after adjusting the tires pressure, the tire may have actually a slow-moving air leak. If the warning irradiate is still on or blinks, there is a break down in the TPM system. See proper manufacturer service information.

NOTE: The tire pressure warning light may turn on as result of natural causes such as herbal air leaks or tires pressure transforms caused by temperature. In this case, adjusting the tire push will revolve off the warning light. Under the complying with conditions, the system may not role properly:

Facilities or gadgets that use comparable radio wave frequencies are situated in the vicinity the the vehicle.A radio maker of similar frequency is used near the vehicle.A the majority of snow or ice cream is grounding to the vehicle, especially roughly the wheels or wheel housings.Tires and wheels are set up that space not equipped v a tire press sensor.Snow tires or tires chains space used. L The battery that the sensor has been depleted.Wheels various other than manufacturer factory wheels space used. If any kind of other wheels 보다 the mentioned ones room used, the system might not function properly due to the fact that the radio tide are differently transmitted indigenous the tire push sensor.Depending top top the tires type, the system may not role properly also though the mentioned wheels space used. L making use of a different form of tires in combination with real tires.

Tire press Sensor Registration

NOTE: when a tire push sensor and/or tire push monitor ECU space replaced, the sensor ID have to be memorized by the tire press monitor ECU. To carry out this procedure, a Toyota Techstream must be used. That is not crucial to it is registered the sensor ID(s) as soon as only tire rotation is performed.

NOTE: prior to beginning registration process on vehicles whereby tire press sensors have actually not to be replaced, retrieve sensor transmitter ID(s) using intelligent tester or by reading the i would on the tire pressure sensor. If sensor is being changed with a new one, do a note of the transmitter ID before installation, together it cannot be checked out after sensor is installed. See Fig. 21.

*

1. Set the tire push of all wheels to pressure specified on the tire and also loading info label.2. Affix the clever tester come DLC3. See Fig. 11.

*
3. Revolve the Tachstream scan device on and the ignition move to on position.4. Go into the complying with menus: Chassis / Tire push Monitor / energy / i would Registration.5. Do the procedure shown on the scan tool.NOTE: Tire press sensor IDs that were previously registered will certainly be deleted from the memory once registration is completed.6. Check the tire pressure sensor’s IDs space registered:7. Get in the following menus: Chassis / Tire push Monitor / Data List.8. Confirm the tire pressure values are shown for all 4 tires.

NOTE: It may take approximately 2 or 3 minutes to upgrade the tire push data. If tire pressure values perform not display screen after 2 or 3 minutes, troubleshoot DTCs C2121/21 come C2124/24 (on some models, up to C2125/25).

See more: How Do You Write 4 3 4 As An Improper Fraction ? How Do You Write 4 3/4 As An Improper Fraction


NOTE: If the ID(s) have not been registered, DTC C2171/71 is set in the tire push monitor ECU ~ 3 minute or more.