Almost any driver have the right to perform this top top their very own if they have actually the crucial materials and also hydraulic jacks. Check out on to learn how to change the oil on your Civic.


This article applies to the Honda civic (1992-2000).

You are watching: 2006 honda civic oil filter location

Honda proposal an oil change when the maintain light come on, or ~ one year—whichever come first. In difficult driving conditions with a the majority of stop-and-go traffic, the maintain light will certainly come top top after about 6,000 miles, which suggests 15 percent that oil life remaining.

*

Materials NeededHydraulic jacks and also jack stands17 mm box finish wrench5W-30 engine oil (4 quarts)FunnelOil drain plug gasketOil drainpipe panOil filter wrenchRagsEngine flushEngine restore

Step 1 – begin the engine and also jack up the car

Warm up the engine come the operation temperatures. This helps to suspend any engine contaminants in the old oil. While the engine is warmed up, prepare and also position the hydraulic floor jack and three ton jack stands. Then, rotate off the engine.

To jack up her car, very first you will should pull the parking brake.Underneath the former passenger"s side, place a jack under the jacking allude of the frame, which is also called the pinch weld (the thicker metal part just behind the front wheel).Lever the jack till you have sufficient room to work-related comfortably under the car.Place a jack was standing under the pinch weld behind the jack.Slowly reduced the vehicle onto the jack stand. Leave the hydraulic floor jack underneath the framework for added support, and also be certain it is not lifting the car above the jack stand.Repeat these measures with the driver"s next of the car.
*
Figure 1. Hydraulic floor jack under the pinch weld.
*
Figure 2. Insert the jack stand alongside the hydraulic jack.

(Related Article: just how to Jack up Your public - usmam.org)

Step 2 – drainpipe the old oil

Remove the oil cap on height of the engine. This will aid the old oil to totally drain.Underneath the car (closer to the engine 보다 the transmission) is a 17 mm hex oil drain plug, facing the behind of the car. Ar the oil pan under this plug.Use a 17 mm box finish wrench to loosen the drainpipe plug 3/4 of a turn.Remove the drain plug by hand, and then allow the oil to drain into the pan.
*
Figure 3. Eliminate the oil drainpipe plug.
Pro Tip

Observe the oil because that shiny specks. Steel flakes in the oil indicates a serious troubles with the internals of her engine.


Step 3 – Clean the oil drainpipe plug and replace gasket

While the oil is draining, wipe off the drainpipe plug through a clean rag. Then, eliminate the old drain plug gasket.Place a brand-new gasket top top the oil drainpipe plug, and also make sure it fits approximately the plug threads.Once the oil has slowed under to a drip, wipe off the area roughly the drain plug v a clean rag.Apply a light coat of fresh engine oil to the object of the oil drain plug come ensure that seals properly.Using the box end wrench, re-install the oil drain plug tightened come a snug fit.
*
Figure 4. Attach a brand-new oil drainpipe plug gasket.
Pro Tip

Alternatively, you can use a speak wrench to verify that the plug is tightened to its exactly specification.


Step 4 – lower the car and also replace oil filter

Jack increase the vehicle with the hydraulic jack, so the is no much longer resting ~ above the jack stand. Eliminate the jack stand, then gradually lower the automobile to the floor.

To replace the oil filter, first locate it. ~ above the firewall next (halfway down the engine block) is wherein the oil filter is located.Using the oil filter wrench, eliminate the old oil filter through rotating clockwise.Before re-installing the brand-new oil filter, apply a irradiate coat of new oil roughly the rubber ring and also threads to ensure it seals properly.Install the new oil filter and tighten it to a snug fit.
*
Figure 5. Removed the jack stand.Figure 6. Apply fresh engine oil to the oil filter.Figure 7. Install the new oil filter.

Step 5 – pour in the brand-new oil

On top of the engine, remove the oil filter cap.insert the funnel into the filler feet to avoid spills.Pour 4 quarts of 5W-30 engine oil (preferably full-synthetic) right into the funnel.
*
Figure 8. Remove the oil filler cap.

See more: I'M Good What About You ?” Than “I'M Good” 4 Better Ways To Respond To “How Are You

*
Figure 9. To water in the new engine oil.
*
Figure 10. Examine engine oil level.
Pro TipsLook in the owner"s hand-operated for the acceptable weights the engine oil for your car.Refer come the orange oil dipstick to determine the oil level in the engine. The optimal of the crosshatched area is the maximum quantity of oil, while the bottom that the crosshatch is the minimum.Take your old oil and also oil filter to a recycling facility. Many auto parts stores and repair shops accept these at no charge.