2005 Kia Spectra front Wheel drive Automatic 72000 milesSpeedometer and also odometer has actually stopped working. Have to I reset the computer by disconnecting battery? wherein is the sensor situated so i can gain a visual to inspect for the obvious?


You are watching: 2005 kia spectra speed sensor location

*

The auto speed sensor going out will cause the speedometer no to work. The connector is situated at the check out the the engine near the bellhousing however the sensor is down near the final drive axle output. This guide will present you wherein the connector is just follow it under to the sensor. (Below)Please let us understand if you need anything rather to acquire the difficulty fixed.Cheers, Ken
*

*

Speedometer quit working totally kinda simply figured it to be the rate sensor. Just would prefer to know how to replace it or if perhaps thats no the problem.
*

It usually is the cause but it could likewise be the wiring and only testings would certainly confirm it. Replacement is a basic job. Disconnect the coupler, eliminate the holding bolt and twist the sensor out.
*

go you change the auto speed sensor? Does your speedometer work correctly?Yes, it might make a difference however it would set a abs code.Roy
Yes adjusted speed sensor and also yes speedometer functions perfectly. Also changed safety switch and there room no ABS codes just the P0501 code
inspect engine light come on. DTC revealed p0501 vss. Ns recently lost my front ideal tire because of some shrapnel on the road. I changed the tire, but the engine light showed up after the incident. I noticed a cable hanging down close to the prior tire. I"m suspect this wire is the vss and also am wonder if this is other I have the right to fix myself? Is there a way to reattach this wire? i was looking online for a diagram and also any valuable information. Deserve to you help?


See more: How Many Small Shrimp In 4 Oz Of Shrimp? Shrimp Sizes And Counts Per Pound

Ok, most most likely it is a abs issue. The very first thing i would do is adjust the tires to the correct size.GENERAL summary The Wheel speed Sensor (WSS) generates a waveform through a frequency proportional come the speed of the vehicle. The signal produced by the WSS notifies the PCM not just if the auto speed is short or high but also if the automobile is or is not moving. The PCM provides this signal to regulate the fuel injection, ignition timing, transaxle change scheduling and also torque converter clutch scheduling. The WSS signal is likewise used come detect rough road conditions.DTC summary The PCM evaluates engine speed and mass air flow if over there is no automobile speed signal. This evaluation of both values will detect open up circuit or brief circuit errors on the wheel rate sensor. The PCM sets DTC P0501 if over there is no vehicle speed signal indigenous wheel rate sensor when both engine speed and also mass air flow are higher than predetermined threshold throughout the predetermined time.DTC Detecting ConditionZoomSized for PrintZoomSized because that PrintMONITOR DTC STATUS affix Connect scan tool and also select "Diagnostic problem Codes(DTCs)" mode.Press F5(INFO) to select DTC information from the DTCs menu.Confirm the "DTC Readiness Flag" indicates "Complete". If not, journey the vehicle within conditions provided in the freeze frame data or allow conditions.Read "DTC Status" parameter.Is parameter displayed "History(Not Present) fault"?NOTE: background (Not Present) error : DTC occurred but has actually been cleared.Present error : DTC is occurring at present time.YES - error is intermittent, resulted in by negative contact in the sensor's and/or PCM's connector or to be repaired and also PCM memory was not cleared. Thoroughly examine connectors for looseness, bad connection, bending, corrosion, contamination, deterioration, or damage. Repair or change as necessary and go come "Verification of vehicle Repair" procedure.NO walk to "Monitor Scan tool Data" procedure. go to "Signal Circuit Inspection" procedure.MONITOR SCAN tool DATA With vehicle raised top top a lift, start the engine and place transaxle in Drive. Let automobile idle and verify speedometer indicates approx. 10 km/h or more(6 mph or more) top top the tool cluster.Connect Scantool and select ABS system.Monitor the "WHEEL SPD SENSOR-FR" parameter top top the existing data list.Specification : 10 km/h or more(6 mph or more)Is value within the specification?YES - Wheel speed sensor is OK. Go to "Signal Circuit Inspection" procedure.NO inspect for open or brief circuit between wheel speed sensor(FR) and also ABS(or ESP) manage module.If problems are found, repair together necessary and also go come "Verification of auto Repair" procedureIf OK, examine wheel rate sensor(FR) as follow :Gap between ABS sensor and trigger wheel (Air void : 0.3 - 1.1 mm (0.011 - 0.043 in ))Trigger wheel problem - Sensor resistance : Approx. 1,300 - 1,500 Ohms at 20 levels C (68 degrees F)Replace wheel rate sensor together necessary and also go to "Verification of car Repair" procedure.SIGNAL CIRCUIT INSPECTION ZoomSized because that PrintCheck for open up in circuit.Ignition "OFF".Disconnect PCM and ABS control Module connectorsMeasure resistance between terminals 39 the the PCM harness connector and also 3 that the ABS manage Module exploit connector(W/ABS)Specification : Approx. 0 Ohm Is resistance in ~ the specification?YES - walk to following step.NO - Repair together necessary and go to "Verification of automobile Repair" procedure.ZoomSized because that PrintCheck for short to soil in circuit.Measure resistance between terminal 39 of the PCM exploit connector and also chassis ground.Specification : InfiniteIs resistance in ~ the specification?YES - check for negative connection in between PCM and also component: backed the end terminal, wrong mating, damaged locks or bad terminal to cable connection. Repair as necessary and go come "Verification of car Repair" procedure.NO - Repair as necessary and also go to "Verification of automobile Repair" procedure.VERIFICATION OF automobile REPAIR ~ a repair, it is vital to verify the the fault has been corrected.Connect scan tool and also select "Diagnostic problem Codes(DTCs)" mode.Press F5(INFO) and confirm that "DTC Readiness Flag" indicates "Complete". If not, journey the vehicle within conditions detailed in the freeze frame data or permit conditions.Read "DTC Status" parameter.Is parameter presented "History(Not Present) fault"?YES - mechanism performing to specification in ~ this time. Clean the DTCNO - go to the applicable troubleshooting procedure.Schematic DiagramZoomSized because that Print© 2016 ALLDATA LLC. All civil liberties reserved. Terms and also Conditions