JavaScript is disabled. For a far better experience, please enable JavaScript in your browser before proceeding.


You are watching: 1999 dodge durango 5.2 water pump replacement

can someone please give me the direction to adjust the water pump on 2000 Durango R/T. Anyone have actually the pages from the FSM the they have the right to post. Many thanks in advanceK
*

This one"s pretty easy, all consideringHTHBillRemoval and also InstallationREMOVALThe water pump deserve to be removed and also installed without discharging the waiting conditioning mechanism (if equipped.)1. Disconnect battery negative cable.2. Drain cooling system.3. Don"t waste recycle coolant. If equipment is clean, drain coolant into a clean container for reuse. WARNING: constant TENSION water tap CLAMPS ARE offered ON most COOLING mechanism HOSES. As soon as REMOVING OR INSTALLING, USE just TOOLS DESIGNED for SERVICING THIS type OF CLAMP, together AS one-of-a-kind CLAMP device (NUMBER 6094.) SNAP-ON CLAMP device (NUMBER HPC-20) may BE used FOR bigger CLAMPS. Constantly WEAR safety GLASSES when SERVICING continuous TENSION CLAMPS. CAUTION: A number or letter is stamped right into the tongue of constant tension clamps. If replacement is necessary, use just an original devices clamp with matching number or letter.4. Eliminate upper radiator hose clamp and hose at radiator.See Figs. 38 and also 375. The heat viscous fan drive is attached (threaded) to the water pump hub shaft. Eliminate fan/viscous pan drive assembly indigenous water pump by turning mounting nut counterclockwise as perceived from front. Subject on viscous pan drive are appropriate HAND. A Snap-On 36 MM fan Wrench (number SP346 native Snap-On Cummins Diesel Tool collection number 2017DSP) and also Special device 6958 Spanner Wrench v Adapter Pins 8346 can be used. Location Special tool 6958 Spanner Wrench onto the water pump pulley-block with Adapter Pins 8346 placed into the holes on the pulley to stop pulley native rotating. Don"t attempt to eliminate fan/viscous pan drive assembly from car at this time.6. If water pump is gift replaced, don"t unbolt fan blade assembly from thermal viscous pan drive.7. Remove fan shroud attaching hardware (two bolts at bottom-two clips in ~ top.)8. Eliminate fan shroud and fan blade/viscous pan drive assembly from car as a complete unit.9. After ~ removing fan blade/viscous fan drive assembly, don"t place thermal viscous fan drive in horizontal position. If stored horizontally, silicone liquid in viscous fan drive might drain into its bearing assembly and also contaminate lubrican"t.10. Eliminate the accessory drive belt.11. Remove lower radiator hose clamp and remove reduced hose at water pump.12. Remove heater water tap clamp and also heater water tap from heater water tap coolant return tube.See Fig. 3913. Ease heater water tap coolant return pipe mounting bolt and remove pipe from water pump. Discard the old pipe O-ring.14. Remove seven water pump mounting bolts.15. Loosen clamp at water pump end of bypass hose. Slip bypass hose from water pump when removing pump indigenous vehicle. Discard old gasket. CAUTION: Don"t pry water pump at time chain case/cover. The machined surfaces might be damaged leading to leaks.INSTALLATION1. Clean gasket adjustment surfaces.2. Making use of a brand-new gasket, download water pump to engine together follows: guide water pump nipple right into bypass hose together pump is being installed. Download water pump bolts. Tighten water pump mounting bolts come 40 Nm (30 ft. Lbs.) torque.3. Place bypass water tap clamp to bypass hose.4. Turn water pump come be sure that pump impeller doesn"t rub against timing chain case/cover.5. Download a brand-new O-ring come the heater hose coolant return tube. Coat the new O-ring with antifreeze before installation.6. Download coolant return tube and its mounting bolt come engine. Be sure the slot in tube bracket is bottomed come mounting bolt. This will certainly properly position return tube.7. Attach radiator reduced hose to water pump.8. Affix heater hose and hose clamp come coolant return tube.9. Install accessory journey belt.10. Place fan shroud and fan blade/viscous fan drive assembly to vehicle as a finish unit.11. Install pan shroud.12. Install fan blade/viscous fan drive assembly to water pump shaft.13. To fill cooling system.14. Attach battery an unfavorable cable.15. Start and warm the engine. Inspect for leaks.


See more: The Sims 2: Pets Wii Cheats, Getting Money On Sims 2 Pets Wii Version!

2001 SLT Plus, 5.9L, PPH Headers, MP 1.7 RRs, M1, and VCs, Fastman 52mm TB, B&G Flash, PIAAs, go Rhino Guards, Tow Pkg, Mag-Hytec Diff & trans Covers, IP CAI, MOAB Basket, "03 front Brakes through drilled and slotted rotors and also much much more!! questioning your medical professional if the Durango is ideal for you.